HD-7P 7,000-lb. Capacity Short Runways Extra-Tall Car Hoist
BendPak HD-7P four post car hoist
Shorter length and extra height, the HD-7P is the ultimate in compact convenience when you want the lifting power of a BendPak in a tight space.

    The HD-7P is a true space-saving powerhouse. The perfect service hoist for shops with limited floor-space or a home car port, the HD-7P requires no special foundation or complicated installation. About the size of a typical parking space, this car hoist doubles nicely as a residential / commercial parking hoist. The applications are endless, but what else would you expect from BendPak? After being in this business for over 40 years, our reputation is as solid as our auto hoists. And if you've ever owned a BendPak, you know that means a whole lot.

    Dependable design
    4 heavy-duty, high-quality, stainless steel lifting cables and a single hydraulic cylinder mounted underneath the runway makes this hoist the most durable, maintenance-free lifting system on the market.

    Dual-hub cable sheaves
    Reduce stress and fatigue on the axles, sheaves and cables. We insist on using dual-hub cable sheaves, even if they cost us more to make. When you buy BendPak, we throw in peace of mind as a free gift.

    Multi-level locking positions
    The HD-7P is equipped with multiple adjustable height locking positions for variable-height parking. A convenient push-button pneumatic safety lock control releases all four independent safety locks simultaneously.

    Heavy-duty aircraft cable
    Each hoist is supplied with 4 high-quality stainless steel lifting cables, rated at 14,400 lbs. each. The combined rating of these cables is more than 822% of the maximum lifting capacity of the entire vehicle hoist! And we make sure it looks tidy too—all lifting cables are fully enclosed within the car hoist structure itself.

    Electric / hydraulic power system
    We incorporate maintenance-free electric hydraulic power systems into each hoist for ultimate dependability, and all controls are conveniently located within close reach.

    Large base plates
    10" x 12" base plates provide a solid foundation for the HD-7P.

    Single hydraulic cylinder
    Leak-Proof-button.jpg
    Each hoist is equipped with a single hydraulic cylinder, hidden away under the runway for minimum exposure and maximum reliable performance. Our industrial-grade hydraulic cylinders feature a single-piece, pilot fitted, machined steel piston, wrapped with specially designed, pressure loaded U-cup piston seals, backups and wear bands to virtually eliminate fluid bypass. The micro-smooth chrome-rod is machined from high-yield, ground and polished C-1045/50 micro-alloy steel and plated to a minimum of .001" diametrically, to ensure superior cylinder operation and life. The superior-design high durometer, mechanically-loaded rod seals make rod leakage is a thing of the past while a specially formulated abrasion-resistant urethane rod wiper provides exclusion protection. The welded cylinder body is made from robust steel tubing produced to exceed ASTM specifications. This combination of superb base material and superior processing ensures that the cylinders remain straight, smooth and last a very long time. An integrated flow restrictor provides a controlled descent in the case of an unexpected hose rupture.

    Durable powder-coat finish
    All HD-Series car hoists feature a durable powder-coat finish that gives the metal a high-quality, extremely durable finish which can withstand even the harshest environmental or chemical conditions. Unlike other companies that claim to powder coat, we take pride in our meticulous 10-step process. First, all parts are visually inspected before being sandblasted. Afterwards, the parts are washed in our 5-stage phosphate tanks that can accommodate parts up to 25' long. Once cleaned, they're immediately dried to avoid rust production, and then outgassed. Outgassing pre-bakes the parts in a curing oven, reducing the possibility of blemishes that may be hiding in the pores of the metal. If not properly outgassed, imperfections in the metal may bubble during the curing process and most likely will cause chips in the powder. After the parts are washed and outgassed, any surfaces and / or threaded holes that need to be masked or plugged, are done so with high-temperature masking tape and silicone plugs. Next, the parts are given a quick thinner wipe to remove any light debris or fingerprints, before being hung on an electrostatically grounded conveyor line. The powder is finally applied using an electrostatic spray gun. The powder “sticks" to the surface in a fashion similar to how dust sticks to a television screen. Once the parts are powder coated, the carts are rolled into our curing oven and baked at 400° F for 45 minutes.

    Caster kit
    Optional 4-piece caster kit makes your car hoist portable, with or without car.

    Integrated design
    Lifting cables, airlines, safety latches and sheaves are all fully enclosed.

    Low-deck runways
    Our low 4-1/2" runways accommodate even the lowest cars.

    Longer approach ramps
    These approach ramps were designed a little longer to help when loading low ground clearance vehicles. It's the little bit that makes a big difference.

    Automatic safety locks
    Aircraft-quality stainless steel and aluminum pneumatic cylinders release all 4 locks simultaneously with the simple push of a button. The spring-loaded safety locks automatically engage continuously as the auto hoist is raised. For added safety, a secondary lock system acts as a slack-cable device to engage in the unlikely event of cable failure.

    *Not all BendPak car hoist models meet the standards as prescribed by AS/NZ 1418.9-(current edition), ANSI/ALI ALCTV-(current edition), ANSI/UL 201. User or Buyer assumes full responsibility for any state, county, federal or international mandated permit, license, code, standard, certification, or any other mandate required related to the installation and/or operation of any BendPak or Ranger product. Read full General Disclaimer details. For more information contact BendPak via: contact@bendpak.com.au

    • 7,000-lb. maximum lifting capacity
    • High lift with short runways
    • Electric / hydraulic power system
    • Single hydraulic cylinder mounted underneath runway
    • Internal anti-sway slider blocks in each column
    • Oversized self-lubricating cable rollers
    • High-speed lifting
    • Features heavy-duty 3/8" aircraft cable
    • Rugged 1-1/4" roller axles
    • Multi-position safety locks in each column
    • Adjustable lock ladders
    • Ramps feature non-skid surface
    • Push-button pneumatic safety release
    • Optional 4,500-lb. capacity rolling jack available (Model RJ-45)

      floorplan-button.jpg

    • Best Warranty Car Lifts - BendPak

      Will your four-post car lift fit?

      Safe balancing for BendPak car lifts

      How to choose the right car lift for you

      BendPak's Top 10 Car Lift Buyers Guide

    • Lifting capacity*: 7,000 lbs. / 3,175 kg
      • *Max capacity / front axle: 3,500 lbs. / 1,588 kg
      • *Max capacity / rear axle: 3,500 lbs. / 1,588 kg
    • Overall width: 99-3/4" / 2,534 mm
    • Outside length: 174" / 4,420 mm
    • Overall length: 200" / 5,080 mm
    • Height of columns: 100" / 2,540 mm
    • Runway min height: 4-1/2" / 114 mm
    • Max rise: 82" / 2,083 mm
    • Max lifting height: 86-1/2" / 2,197 mm
    • Width between posts: 89-3/4" / 2,280 mm
    • Runway width: 19" / 482 mm
    • Width between runways: 37-1/2" / 952 mm
    • Runway centerline: 56-1/2" / 1,435 mm
    • Outside edge of runways: 75-1/2" / 1,918 mm
    • Drive-thru clearance: 76-1/2" / 1,943 mm
    • Length of runways: 164" / 4,166 mm
    • Min wheelbase @ rated capacity: 115" / 2,921 mm
    • Min wheelbase @ 75% capacity: 100" / 2,540 mm
    • Min wheelbase @ 50% capacity: 85" / 2,159 mm
    • Min wheelbase @ 25% capacity: 70" / 1,778 mm
    • Locking positions: 15
    • Lock spacing: every 4" / 102 mm
    • Lifting time: 35 sec
    • Motor: 220 VAC / 60 Hz / 1 Ph
    • Shipping weight: 1,942 lbs. / 883 kg
    • Shipping dimensions: 172" x 29" x 54" / 4,369 mm x 737 mm x 1,372 mm

    Note: An air supply (minimum: 30 psi / 3 CFM) is required for the safety-lock mechanisms to function. It is solely the responsibility of the end-user to provide, install and maintain the air supply.

    *Not all BendPak lift models meet the standards as prescribed by ANSI/ALI ALCTV-2006 or ANSI/UL 201. Consult www.autolift.org for a complete list or contact BendPak via contact@bendpak.com.au

    BendPak HD-7P four post car hoist
    BendPak HD-7P four post car hoist
    HD-7P four-post cable block
    HD-7P power unit pump assembly
    HD-7P cable sheave rollers
    HD-7P air lock safety release assembly
    HD-7P secondary slack safety locks
    HD-7P runways with solid steel deck
    http://www.bendpak.com/HD-7P.pdf

    Featured accessories for the HD-7P


    What customers are saying about HD-7P Car Lifts by BendPak



    "I have a BendPak four post car hoist and couldn't work on cars without it."

    - oldmodman on svtperformance

    "I have a BendPak four post hoist. It is about 4 years old and has a 7,000 pound capacity. I went with that one due to it's being 120v instead of 220 like all the heavier duty lifts...It has been trouble free."

    - oldmodman on svtperformance
    deliverydetails.jpg

    Request More Info on the HD-7P!

    Quick Specs

    Lifting capacity: 7,000 lbs.
    Overall width: 99-3/4"
    Overall length: 200"
    Height of columns: 100"
    Max rise: 82"
    Length of runways: 164"
    Motor: 220 VAC / 1 Ph
    ALI-ETL-button.jpg
    View Full Specs »
    ©2012 BendPak, Inc. All rights reserved. Site Map | Policies | Feedback | Social Connect | FTP | Español | Français | 日本 | العربية
    SEO Friendly CMS by Pixelsilk